Tiles are a major item in the current renovation. Tiles are mostly used in kitchens, toilets, balconies and other places. The biggest advantage of tile decoration may be dirt resistance, and the main problem is the treatment of the waterproof layer, because most of the places in the kitchen and toilet water problems, so the waterproof wall should pay more attention.
New houses that are not waterproof or old houses that need to replace tiles need to be re-waterproofed. The main method for the treatment of the water-repellent layer is: a suitable waterproof agent at a height of 1 meter on the ground and walls, such as a waterproof agent No. 911. The location of the wall above 1 meter can use a bit of asphalt oil for waterproofing. If the economy is not allowed, you can also directly use asphalt or resin to waterproof the floor. 20 cm on the ground and the ground must be thick.
The new house is made of waterproof layer. After construction, it should be noted that the inspection surface should have no voids. After the old house is demolished, you need to do a simple cement batch heat before you can make a waterproof layer.
After the tile construction, if there is any damage that needs to be repaired, care must be taken. If the position is low, the waterproof layer may be broken during the removal. Before the new brick is filled, the waterproof layer is also repaired before the tiles can be tiled. After finishing the renovation, try to avoid drilling holes in places less than 1 meter high.
Wall decoration latex paintLatex paint is a very popular decoration practice and is currently the mainstream of wall treatment.
In the secondary decoration, before the latex paint is applied, the original coating layer is based on the following three principles:
1. The wall of a new house generally only needs to be polished with coarse sandpaper, and it is not necessary to eradicate the original paint layer.
2. The walls of ordinary old houses generally need to be removed. The method is to wet the surface with water first, then use a trowel or electric planer to remove the surface paint.
3. For the old, disrepaired walls, the surface has been severely peeled off, and the hot layer has been chalked. It is necessary to remove the paint layer and the entire batch until it is seen as hot or brick.
4, then use the fly powder and cooked rubber powder mix and mix bottoming lot, then paint latex paint, the surface layer to be painted 2 to 3 times, the time between each pass is better than 24 hours.
Wall decoration wallpaperWallpaper is widely used for wall decoration, its types are mainly paper wallpaper, chemical fiber wallpaper, plastic wallpaper, and cloth wallpaper is generally called wall cloth, not classified as wallpaper. Wallpaper can be printed patterns, patterns change, rich color, and the construction is convenient and fast.
The most important key technology in the construction of wallpaper is the problem of mildew prevention and handling of stretchability:
1) Anti-mildew treatment. Before the wallpaper is posted, it is necessary to treat the base surface first, and the flying powder and the cooked rubber powder may be used to perform batch heating and leveling. After it is dry, apply a varnish one or two times and post it again.
2) Scalability treatment. The scalability of wallpaper is a chronic problem. To solve it is to start with prevention. On the one hand, we must reserve 0.5mm overlapping layers. There are some people who unilaterally pursue aesthetics and cancel this overlap. This is not appropriate. In addition, try to buy some good scalability wallpaper.
Wall decoration spraySpraying is a brushing method for water-soluble paints. Using the characteristics of oil-in-water, a pressurized spray gun is used for construction. Can form a variety of color textures, the effect is elegant and three-dimensional.
The main advantage of the spray construction method is rapid construction, which can greatly shorten the construction period. The disadvantage is that it is difficult to maintain at a later stage and it is easy to injure the entire surface due to a small part of it. Unless it is treated in large areas, it cannot be restored to its original shape.
In addition, it should be noted that if the metal surface is painted, it is best to use metallic paint (magnetic paint).
Wall construction wall decoration
Full Body Protection Suit,Disposable Protective Clothing,Industrial Protective Clothing,Disposable Protective Coveralls
Ningbo Autrends Prevention Products Co., Ltd , https://www.autrendsafety.com