In order to get a little more than 123 the thrill of overclocking, 456 is a common problem. There are countless fans used at hand. One day, when the fan clip was suddenly accidentally hit, the 456 socket was accidentally broken and broken, and it was removed from the chassis. Under the upgrade 789 motherboard looked at the broken plastic hook, there is a feeling of crying and tears. But the computer can't be used, or find a way to install the fan. I remember that there was a paper on how to fix the hard disk with a rubber band. If you use it on a fixed fan, you need to solve two problems: one is to fix the fan firmly on the 56 and not to move it; the other is to keep it for a long time. The constant tension rubber band is obviously not suitable for fixing 56. It is too hot for a long time. The rubber band will soften the fan and it is easy to fly out. There is a potential risk of burning 56. If it's not soft, then it's hard. It's all elastic. Why don't you use springs instead of rubber bands? This idea is good to say dry, so the cassocks have three things from the bottom of the box, the same length of spring: small screws , a small nut, a small washer.
Then, the electric iron pliers were taken out from the toolbox, and a room temperature curing epoxy adhesive was specially purchased. The chemical store is available for sale. The morning light is a concept of how to do this spring fan. Let me take a look at my idea. The role of the spring in the inside is to hook the fan "to make the bottom of the fan heat sink intimately contact, to ensure that the heat is quickly lost, one end of the spring is hung on the screw hole on the corner of the fan; the other end is fixed on the main board, maybe you have to ask, There are so many dense circuit wiring on the motherboard, there is an empty place to hang the spring, and I have no courage to drill holes on the motherboard. There is only one way to stick the nut to the predetermined position, and wait for it to be completely firm. After tightening the screw, the head of the screw is welded with a small washer, which solves the problem of the spring hook. The starting point, the position of the position, the location of the four points of focus is a very critical factor, the capacitance around the 56 socket is relatively large. When the amount is narrow, gently press the fan on the 56 and the spring hooks on the corner. Stretch the spring to the appropriate position and angle. It is best to have two pairs of oppositely spaced on both sides of the 56 to tighten the fan without swinging. It is advisable to try again and again to find the best position and mark it. Welding the screw and spring to hook the screw without the eye is not enough. Press the washer vertically into the slot of the screw cap and solder the iron. Tin solders them firmly.
Assemble the fan, screw the screw with the washer into the nut on the main board, tighten the screw with the pliers, and hook the spring. Then apply a small amount of silicone grease, put the fan holder up, fix the position and press it, then use the needle-nosed pliers to hook the other end of the spring to the screw hole on the corner of the fan. Here we must master the length and extension of the spring. The four springs should maintain the same angle and tension. After the fan is turned on, the fan will not swing or shift. Experience articles, the special spring fan is finally done, don't busy booting, I have to use the electronic thermometer to monitor the temperature of the Duron in real time, just raise the fan a little and press the temperature probe to a corner under the fan. That's it. Put the motherboard with the good spring fan back into the chassis, remove the hard disk and shake the fragile guy to turn it on again. The electronic thermometer immediately shows the temperature. The system did not find the hard disk display boot failure, no matter whether it continues to let the computer run empty, and then watch the temperature fluctuation of the electronic thermometer is stable after moving, now use the violent method to check the firmness of the spring fan and the contact, knock a beat A shot of the chassis, the temperature does not jump at all and then the chassis is hung up, the fan is still moving, the card is a bit tight, but fortunately not crushed. If you buy the motherboard as usual, it will cost you to change the socket. You can't fix it right away. Using the method described in this article to make a spring fan with simple and easy-to-find materials is not difficult, let alone my ABIT motherboard resurrected. From the measured results, the cooling effect is not inferior to the normal state. When your fan encounters a similar problem, you may wish to change your position and think about any way to fix the fan well. Maybe a new alternative fan is born in your hand. It is.
XBW Breakers are most competitive price and quality demolition hammer, demolitions, demolition hammers, Demolition Breakers,rotary breaker, Rotary Demolition Hammer.
We make main motor house,motor,aluminium parts,gear box and so on.So we could make more competitive price.Because we have these machinery workshop,so we also could make high quality.
Our chuck use easy changing.So could give you very high efficiency working feeling.Easy and fast working , dragon can.
XBW Demolition Breakers, XBW Demolition Breaker Hammers, XBW Demolition Hammers, Electric Demolition Hammer
Yongkang Longneng Power Tools CO., LTD. , http://www.longnengtool.com