Finishing (such as cutting) of the machined surface by the relative movement of the lap and the workpiece under a certain pressure by the abrasive particles coated or pressed onto the lap. Grinding can be used to process a variety of metal and non-metallic materials, the surface shape of the processing is flat, the introduction of the abrasive particles coated or pressed into the lap, through the relative movement of the rig and the workpiece under a certain pressure on the surface Finishing (such as cutting). Grinding can be used to process a variety of metal and non-metallic materials, the surface shape of the processing is flat, inner and outer cylindrical and conical surfaces, convex, concave spherical, thread, tooth surface and other profiles. The processing precision can reach IT5~01, and the surface roughness can reach Ra0.63~0.01 microns.
Classification Grinding methods can be generally divided into three categories: wet research, dry research and semi-dry research.
1 Wet grinding: Also known as sand grinding, the liquid abrasive is continuously filled or coated on the grinding surface, and the abrasive continuously slides and rolls between the workpiece and the lap to form a cutting motion. Wet grinding is generally used for coarse grinding, and the fine powder abrasive used has a particle size coarser than W7.
2 dry research: also known as sand embedding, the abrasive is evenly embedded in the surface layer of the lap, only a small amount of stearic acid mixed fat and other auxiliary materials must be applied on the surface of the lap. Dry grinding is often used for fine grinding, and the fine powder abrasive used is finer than the W grinder 7.
3 Semi-dry research: similar to wet research, the abrasive used is a paste-like paste. Grinding can be done either manually or on a grinder. Before the workpiece is ground, it must be processed by other processing methods to obtain higher pre-machining precision. The remaining grinding allowance is generally 5 to 30 microns.
The lap is a tool for grinding and shaping the workpiece, and at the same time is a carrier for the abrasive. The hardness should be lower than the hardness of the workpiece and have a certain wear resistance. It is usually made of gray cast iron. The metallographic structure of the wet research tool is mainly ferrite; the dry research tool is made of uniform and fine pearlite. A mild steel lap is commonly used when grinding threads below M5 and small workpieces with complex shapes. When grinding small holes and soft metal materials, brass and copper laps are mostly used. The lap should have sufficient rigidity and the working surface should have a high geometric accuracy. The lap is also subject to cutting and wear during the grinding process. If it is operated properly, its precision can also be improved, so that the machining accuracy of the workpiece can be higher than the original precision of the rig.
Correct handling of the trajectory of the grinding is an important condition for improving the quality of the grinding. In the plane grinding, the general requirements: 1 the movement of the workpiece relative to the lap, try to ensure that the grinding stroke length of each point on the workpiece is similar; 2 the workpiece trajectory evenly spreads over the entire lap surface to facilitate uniform wear of the rig; The curvature of the trajectory should be small to ensure the smooth movement of the workpiece; 4 the trajectory of any point on the workpiece should avoid premature periodic repetition. The picture shows the commonly used plane grinding motion trajectory. In order to reduce the heat of cutting, the grinding is generally carried out under low pressure and low speed conditions. The pressure of rough grinding does not exceed 0.3 MPa, and the pressure of lapping is generally 0.03 to 0.05 MPa. The speed of rough grinding is generally 20 to 120 m/min, and the speed of lapping is generally 10 to 30 m/min.
Http://news.chinawj.com.cn Editor: (Hardware Business Network Information Center) http://news.chinawj.com.cn
Fiberglass pool screens have revolutionized the way pool owners enjoy their outdoor spaces. These screens are specifically designed to enclose pool areas, providing a range of benefits for both safety and comfort. Made from a durable and weather-resistant fiberglass material, these screens effectively keep out debris, leaves, and insects, ensuring a clean and enjoyable swimming experience. The fine mesh construction allows for optimal airflow and natural light, while still maintaining privacy. Fiberglass pool screens are also resistant to corrosion and fading, making them a long-lasting solution for pool enclosures. Whether you're looking to create a safe environment for children or simply want to enhance the aesthetics of your pool area, fiberglass pool screens offer a practical and stylish solution.
Fiberglass Pool Screen, Swimming Enclosure, Outdoor Protection
Jinwu Glass Fiber Co., Ltd , https://www.jwglassfiber.com